220 lines
12 KiB
Plaintext
220 lines
12 KiB
Plaintext
#65
|
|
|
|
TUNE YOUR MINI -14 by James Mason
|
|
From Guns & Ammo/March 1987
|
|
|
|
With the introduction of the Mini-14 rifle, Sturm, Ruger wrought a
|
|
major coup in the field of firearms. This lightweight .233 caliber
|
|
rifle displaced the M1 Carbine in the hearts and minds of many
|
|
American shooters.
|
|
|
|
The scale, weight, and military presence of the Mini-14 made it an
|
|
instant hit... the .223 cartridge being vastly superior to .30 caliber
|
|
M1 Carbine ammo. Few firearms have so instantly filled a market niche
|
|
as the Mini-14.
|
|
|
|
Over the years, shooters have come to realize a few shortcomings in
|
|
the Mini-14. The factory corrected one of these when it brought out
|
|
the Ranch Rifle by equipping it with scope blocks and low side
|
|
ejection of fired cases. The other concern has to do with accuracy.
|
|
The Mini-14 was never designed for match shooting and delivers 3 to 4
|
|
inch groups at 100 yards; throw in the usual "human factor" and that
|
|
score reads 4 to 6 inch inconsistent groups.
|
|
|
|
The average Mini-14 owner is not necessarily an accuracy buff, but the
|
|
latterday generation has come to expect smaller groups from all
|
|
rifles. Many shooters are adept at doing minor repairs on their own
|
|
guns, and tuning the Mini-14 for its performance potential makes a
|
|
good weekend project for the off-season.
|
|
|
|
With appropriate references to "kitchen table" gunsmithing, there are
|
|
three areas where work on the Mini-14 will pay off in tighter groups.
|
|
This is a serious project that, while not overly difficult to perform,
|
|
requires attention to detail from the amateur gunsmith.
|
|
|
|
Stock bedding, Trigger group modifications, and sights are the areas
|
|
that best reward diligent attention. Tailored handloads can also
|
|
contribute toward accuracy and will be discussed, but this is outside
|
|
the reaim of a gunsmithing activity. Besides, a lot of Mini-14
|
|
shooters do not reload, and depend upon commercial or remanufactured
|
|
ammunition and foreign military fodder.
|
|
|
|
A discussion of some Mini-14 design realities helps put this project
|
|
in perspective. As was mentioned above, the Mini-14 was not designed
|
|
as a match gun. It has a thin, low-mass barrel with gas-impulse
|
|
actuation. The barrel will vibrate from firing alone, but gas impulses
|
|
against the relatively heavy inertia operating slide cause further
|
|
disturbances to barrel nodal movement.
|
|
|
|
The Mini-14 gas system uses a hollow, fixed piston though which
|
|
propellant gases impinge on the operating slide. There is no
|
|
contained, modulated piston stroke. So, the reaction to the gas pulse
|
|
induces a slight bending movement on the mid-barrel section-enough to
|
|
disturb normal barrel vibrational rhythms.
|
|
|
|
The Mini-14 has a good quality birch stock, which is quite stable, but
|
|
not overly stiff, due to the thin wall sections around the receiver
|
|
and fore-end. New guns are factory fitted to provide some stiffness,
|
|
but after shooting a couple of thousand rounds, setting of parts makes
|
|
the stock fit a fairly loose proposition. Rebedding can restore that
|
|
stiffness and assure support for the Mini-14's operating elements.
|
|
|
|
Trigger pull characteristics on all military rifles leave a lot to be
|
|
desired. The safety aspects of two stage pulls need not be sacrificed,
|
|
but a properly regulated trigger job can produce a 4 to 4 1/2 pound
|
|
letoff that will do more to reduce the effect of the human factor than
|
|
anything else, with the exception of a better sight system.
|
|
|
|
The coarse-adjusted military sight on the factory Mini-14 is suited to
|
|
the original design objectives of the rifle. It is okay for a rifle
|
|
designed to shoot 3 to 4-inch groups. But, adjustment stops and
|
|
aperture design limit it for more demanding shooting. Millett Sights
|
|
(16131 Gothard Street, Dept. GA, Huntington Beach, California 92647)
|
|
understands the needs of more demanding Mini-14 shooters, and have
|
|
adopted their Series 100 Sight to the Mini-14 and other assault-type
|
|
rifles. The result is a first-rate replacement peep sight that meets
|
|
the needs for realizing the performance potential of the Mini-14.
|
|
|
|
Positive, 1/3-minute click-adjustments on the Millett sight allow for
|
|
both windage and elevation. A large match-style eyepiece shields the
|
|
eye from glare. The standard .080-inch aperature (.050-inch is
|
|
optional) provides a crisp, clean sight picture; the aperature hole is
|
|
reverse tapered, like top-grade match sights, so no "tunnel effect"
|
|
distort aperture edges. The Millett sight base fits directly into the
|
|
Mini-14 receiver and is secured by a single throughpin-a simple, easy
|
|
installation once the factory sight is removed. The installation makes
|
|
a handsome complement to the Mini-14 receiver.
|
|
|
|
The factory Mini-14 front sight blade is an exposed, serrated ramp
|
|
with a slightly tapered silhouette. There are several possible
|
|
replacements available for this front sight unit. The Choate front
|
|
sight and flash hider unit makes a good replacement choice and was
|
|
installed on our conversion. The Choate front sight blade is a
|
|
military post with "ears". The flash hider is of the bird cage type,
|
|
and is solid on the bottom, providing muzzle stability during firing.
|
|
|
|
A well-bedded stock adds to stiffness and support of the operating
|
|
elements. While new Mini-14's may fit well, continued firing will
|
|
loosen up the stock and receiver union. By using a non- shrinking
|
|
stock bedding compound such as Accraglas glas, support for receiver
|
|
legs, the operating rod guide channel and the stock ferrule can be
|
|
reinforced. Dismantling the stock allows removal of the stamped sheet
|
|
metal recoil stop that fits inside the receiver magazine opening A
|
|
thin coat of bedding compound under these supporting structures adds
|
|
to the stiffness of the midsection of the stock and assures minimal
|
|
creep of the recoil stops. After treating metal parts with parting
|
|
compound, lightly apply epoxy to the wood then replace the recoil stop
|
|
in the stock and tighten the side screws. Let this piece cure
|
|
overnight.
|
|
|
|
Next, remove the stock ferrule and the sheet metal action slide guide.
|
|
Butter the stock seating area for these parts and replace the metal.
|
|
Again, be sure to coat the metal with parting compound before
|
|
contacting the bedding compound.
|
|
|
|
Using silicone parting agent, spray the inside surfaces of the gas
|
|
piston collar assembly and butter the outer surface of the stock
|
|
ferrule with compound. At the same time, spray the receiver legs and
|
|
bottom of the receiver with parting agent. Butter the receiver leg
|
|
channels in the stock to fill in the area below, in front and to the
|
|
sides of the receiver legs where they seat in the stock. Assemble the
|
|
barrel/receiver group in the stock using a large rubber band to hold
|
|
the stock and receiver together. Let this work cure overnight after
|
|
wiping off any excess bedding compound that oozes out of joints. A
|
|
little oozing shows a proper amount of compound; don't overapply, but
|
|
use enough to fill all the voids. Failure to use parting agent can
|
|
result in embarrassment. You might permanently bond the stock and the
|
|
receiver together!
|
|
|
|
Separate the stock the next day, then carefully chisel out any excess
|
|
ridges on the inside of the stock. Small bubbles in the work may be
|
|
refilled. Reassemble the stock and insert and secure the trigger
|
|
assembly. Observe any looseness of the trigger assembly. This may
|
|
require additional bedding under the flat contact pad on the bottom
|
|
outside edge near the middle of the receiver.
|
|
|
|
Use parting agent on the receiver bottom, then apply bedding compound
|
|
on the stock surfaces adjacent to the receiver pad. Reassemble the
|
|
rifle, insert the trigger group, but close the trigger guard down only
|
|
to about 1/2 inch away from its hooking point. Let the epoxy cure,
|
|
then clamp the triggerguard shut. This technique assured a very solid
|
|
stock-to-barrel/receiver fit, necessary for consistent shooting
|
|
accuracy.
|
|
|
|
Trigger work calls for smoothing burrs and surface roughness off of
|
|
sear/hammerhook engagement surfaces. First disassemble the trigger
|
|
group and arrange the parts so hard stoning of the contact areas can
|
|
be done without altering engagement angles. Dressing hammerhooks and
|
|
sear surfaces amounts to a few deft strokes only. As a rule, when
|
|
people feel they have done enough, too much stoning has been
|
|
accomplished. Overstoning will reduce trigger pull letoff weight to
|
|
below 3 1/2 pounds, making trigger release unpredictable in an
|
|
autoloading rifle. Too light a pull can cause the gun to "double" or
|
|
"triple" due to the rocking motion of recoil and return-to-battery of
|
|
the enertia slide. A 4 to 4 1/2 pound pull is ideal with little or no
|
|
sensation of cheep. The classic two-stage military pull characteristic
|
|
should definitely be maintained.
|
|
|
|
A word of warning is in order here. Trigger adjustments demand
|
|
experience and a definite "feel" for the job. A poor trigger job can
|
|
ruin an otherwise good rifle. It is possible to make the piece unsafe
|
|
if the adjustment is botched. Amateurs who may do other gunsmithing
|
|
perfectly well may have no particular skill at trigger adjustment.
|
|
Unless individuals are experienced at regulating a trigger pull, the
|
|
job is best done by a trusted professional. The rewards of a well
|
|
regulated trigger are essential for rifle accuracy, so take your
|
|
Mini-14 trigger group to a competent local gunsmith or put it in a
|
|
padded mailing envelope along with a check or money order for $35.00
|
|
and send it to: Poway Gun Works, 13168 Poway Road, Dept GA, Poway,
|
|
California 92064 to have it done right.
|
|
|
|
Field testing comes after the bedding, trigger regulation and sight
|
|
installation. The test rifle was first fired with some surplus Lake
|
|
City Arsenal '67 vintage ammunition. Center zero was established at 25
|
|
yards with intermediate (50 yards) firing and later 100-yard groups
|
|
fired off the bench. Shooting was done in early morning with very
|
|
little of no crosswind.
|
|
|
|
Our early groups were erratic and disappointing, but, as firing
|
|
continued, the rifle settled into its bedding and groups converged on
|
|
zero. Early cold-barrel groups were respectable in the 2-3 inch size.
|
|
But groups "walked" with a vertical string as the barrel heated up.
|
|
Once the bedding was seated and the gun heated uniformly, the best
|
|
groups appeared.
|
|
|
|
After things settled down and became consistent, a switch to Remington
|
|
.223 commercial ammunition produced groups up to the full potential of
|
|
the gun. The best six-round group measured 1.6 inches at 100 yards. It
|
|
would be good to try Winchester and Federal Commercial loads in
|
|
individual guns to observe the result. None of these brands were
|
|
available on our test day, however. Nobody can complain about 1 1/2
|
|
minutes of angle with a Mini-14!
|
|
|
|
The Choate front sight is investment cast and the top post corners are
|
|
very slightly rounded. Flat filing squares up the post. Millett's
|
|
sight base with the Choate post combination made the gun shoot
|
|
high-about 12 inches high at 100 yards. Millett has since modified
|
|
their base to correct for this.
|
|
|
|
Bedding effects are intrinsic to such good groups. But the trigger job
|
|
and crisp, effective Millett sights were appreciated as aids to
|
|
practical accuracy. Shooter confidence imparted by this tuning was
|
|
evident shortly after firing began.
|
|
|
|
Custom handloads would probably shrink groups further, but the effects
|
|
would not necessarily contribute as much as if the loads were fired in
|
|
a bolt-action rifle. The need for cannelured bullets and crimping with
|
|
self-loading ammunition, along with loose chamber dimensions of
|
|
self-loader, limits accuracy contributions of carefully assembled
|
|
custom loads in the Mini-14.
|
|
|
|
So, there it is! An attainable project for the Mini-14 owner who wants
|
|
to get the most out of his rifle. For just a couple of evenings' time
|
|
and the price of materials, you can upgrade the rifle's handling
|
|
characteristics as well as accuracy and performance. And, for riflemen
|
|
who care, there is the self-satisfaction of having made their Mini-14
|
|
perform.
|
|
|
|
=======================================================================
|
|
|
|
|