92 lines
4.1 KiB
Plaintext
92 lines
4.1 KiB
Plaintext
SHORTWAVE CONVERTER
|
|
|
|
Parts List
|
|
|
|
C1 Optional capacitor. Use 150pF with 5 Mhz crystal, or 47pF with 8 Mhz
|
|
If using crystal ò 10 Mhz omit this capacitor.
|
|
|
|
C2 33 pF
|
|
C3,C5 220 pF
|
|
C4 .047 æF
|
|
D1 Zener diode between 5.1v - 6.2v (2N4691 or equivalent)
|
|
R1 1Kê, ¬ watt resistor
|
|
U1 NE602N Frequency Converter IC
|
|
T1 10.7 Mhz miniature IF transformer (green core)
|
|
XTAL 5 Mhz or 8 Mhz crystal, or other values (see text file XTAL.TXT)
|
|
One for each band you like to listen to
|
|
|
|
8-pin DIP socket (for U1)
|
|
|
|
J1,J2 RCA jacks [J2 is optional, see note 3 below]
|
|
|
|
Motorola plug (optional. If installing converter externally, use for
|
|
connecting cable to car radio's antenna jack). Radio Shack parts #274-711
|
|
|
|
14-pin wire-wrap socket and 14-pin DIP headers for mounting crystals
|
|
Optional (see file XTAL.TXT)
|
|
|
|
Hookup wire
|
|
|
|
|
|
|
|
Schematic
|
|
=========
|
|
|
|
|
|
ÚÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÂÄÄÄÄÂÄÄ/\/\/\Ä +12v
|
|
³ ÄÄÁÄÄ ³ ³ R1
|
|
ÄÁÄC3 ÚÄÄÄ¿ xtal ³ ³
|
|
ÄÂÄ ÀÄÄÄÙ ³ ³
|
|
³ ÄÄÂÄÄ ³ ³
|
|
J2 (to car radio antenna jack) ³ ³ ³ ³
|
|
ÚÄÄ¿ C5 ÚÄÄÁÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÁ¿ ³
|
|
³ oÄÄÄÄÄÄÄĶÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ´ 7 6 8³ ³
|
|
ÀÄÂÙ ³5 ³ ³
|
|
ðgnd ³ U1 ³ ³
|
|
³ ³ ³
|
|
J1 (ant.) ÚÄÄÄÄÄÄÄÄÄ¿ ³ NE602 ³ ³ ¿ D1
|
|
ÚÄÄ¿ ³ 3ÃÄÄÄÄÄÂÄÄÄÄ´ ³ ÃÄÄÄÄ´ÄÄÄÄÄÄÄÄ¿
|
|
³ oÄÄÄÄÄÄÄÄ´1 ³ ³ ³ Frequency ³ ³ À ³
|
|
ÀÄÂÙ ³ T1 4ÃÄnc ÄÁÄC1*³ Converter ³ ³ ³
|
|
³ ³ ³ ÄÂÄ ³ ³ ³ ³
|
|
ÃÄÄÄÄÄÄÄÄ´2 ³ ³ ³ ³ ÄÁÄ ³
|
|
³ ³ 5ÃÄÄÄÄÄÁÄÄÄÄ´ ³ ÄÂÄ C4 ³
|
|
³ ÀÄÄÄÄÄÄÄÄÄÙ ³ 3 ³ ³ ³
|
|
³ ÀÄÄÄÄÄÄÄÄÄÄÄÄÂÄÄÄÄÄÄÄÄÄÄÙ ³ ³
|
|
³ ³ ³ ³
|
|
ÀÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÅÄÄÄÄÄÄÄÄÄÄÄÄÄÄÁÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
|
|
ðgnd
|
|
|
|
|
|
-----------------------------
|
|
Notes:
|
|
|
|
1) Virtually any construction method (point-to-point wiring, wire wrapping,
|
|
etc.) should work, but a printed circuit board is recommended for both
|
|
ease and neatness of construction. PC board construction would probably
|
|
also help minimize undesirable RF interference from strong local broadcast
|
|
stations. See file READ.ME for source of PC board.
|
|
|
|
2) Connect external antenna to J1 (it works with anything over 2', but better
|
|
results are obtained with longer lengths.
|
|
|
|
3) J2 connects to car radio's antenna jack. If mounting the converter inside
|
|
the car radio, omit J2 and run a wire directly from where the center
|
|
connector of J2 is indicated to the car radio's antenna jack, otherwise
|
|
use coax cable to connect from J2 to car radio antenna jack (see note 3).
|
|
|
|
4) It is strongly suggested that you install the converter inside the
|
|
chassis of the car radio (it simplifies the wiring and reduces noise). If
|
|
you do not have room to do so, use a metal case for the converter and a
|
|
SHORT length of shielded coax cable for the connection from the converter
|
|
to the car radio's antenna jack.
|
|
|
|
5) Connect +12 volt power input to car radio's on/off switch. That way you
|
|
can turn both radio and converter on with that switch.
|
|
|
|
6) When everything is working, tune in a shortwave station near the middle of
|
|
the dial and adjust the slug of T1 for the strongest signal.
|
|
|
|
7) You may use a signal generator or crystal oscillator to calibrate the
|
|
dial, if desired.
|