262 lines
10 KiB
Plaintext
262 lines
10 KiB
Plaintext
-----------------------
|
|
How to build a BLUE BOX
|
|
-----------------------
|
|
|
|
We all know that the touch tone frequencies are composed of 2 tones (2
|
|
different frequencies) so that is the reason why we have 2 VCO's (Voltage
|
|
Controlled Oscilators). We will call then VCO#1 and VCO#2. If you have
|
|
noticed VCO#1 and VCO#2 are exactly the same type of circuits. That is why
|
|
only 1 was drawn. But remember that whatever goes for VCO#1 also goes for
|
|
VCO#2. Both VCO'S are composed of a handfull of part. One chip, two
|
|
capacitors, 2 resistors and five potentiometers. All of this will give you
|
|
(when properly calibrated) one of the freqencies necessary (the other one
|
|
will come from VCO#2) for the operation of the Blue Box. Both of these freqs.
|
|
will be mixed in the speaker to form the required tone.
|
|
|
|
This is one of the most sophisticated designs I have ever made. Why?
|
|
Because other designs will drain the battery after 10 calls. This design will
|
|
make them last 10 months!!!!! But never the less, don't forget to put in a
|
|
switch for on and off. Ok let's build the two VCO'S and calibrate the unit
|
|
before we get to the keyboard construction.
|
|
|
|
VCO CONSTRUCTION:
|
|
----------------
|
|
|
|
TOOLS REQUIRED
|
|
|
|
1 ocilliscope(optional but not req)
|
|
1 Freq. counter (REQUIRED)
|
|
1 Volt meter " " "
|
|
Electronics tools (Pliers,drll,
|
|
screwdrivers, etc.)
|
|
|
|
=====================================
|
|
|
|
PARTS
|
|
|
|
R1 1.5K RESISTOR 5%
|
|
R2 1K RESISTOR 5%
|
|
C1 .1uf ELECTROLYTIC CAPACITOR 16VDC
|
|
C2 .01uf " " (MYLQR)16VDC
|
|
IC1 2207 VCO CHIP BY EXAR ELECTRONICS
|
|
Remember the above only says
|
|
VCO#1 but the same is for VCO#2
|
|
R3-R4 150 OHM RESISTORS 5%
|
|
C3-C4 .1 uf ELECTROLITIC CAPACITOR
|
|
10VDC
|
|
P1-P10 200K TRIMMER POT - 20 TURNS
|
|
DIODES USED IN THE KEYBOARD
|
|
ARE 1N914 TYPE (40 OF THEM) &
|
|
13 SWITCHES FOR THE KEYBOARD
|
|
SPST MOMENTARY.
|
|
SPKR=YOU CAN USE A TELEPHONE SPEAKER
|
|
FOR THIS (IT WORKS BEST) BUT
|
|
REMEMBER TO TAKE OUT THE DIODE
|
|
THAT IS CONNECTED ACCROSS IT.
|
|
|
|
=======================================
|
|
|
|
IMPORTANT NOTES
|
|
|
|
1. DO NOT USE ANYTHING ELSE OTHER
|
|
THAN A MYLAR CAPACITOR FOR C2.
|
|
2. PINS 10,9,8 SHOULD BE TIED
|
|
TOGETHER AND BE LEFT FLOATING.
|
|
3. ALL RESISTORS SHOULD BE 5%!
|
|
NOTHING ELSE!
|
|
4. A TELEPHONE SPEAKER GIVES THE
|
|
BEST RESULTS.
|
|
|
|
=======================================
|
|
|
|
TROUBLE SHOOTING
|
|
|
|
By now you should have constructed the two VCO'S on a bread board or
|
|
anything that pleases you. Check for cold solder joints, broken wires,
|
|
polarity of the battery, etc. Before we apply power to the VCO'S we have to
|
|
adjust the pots for their half way travel point. This is done by turning them
|
|
21 turns to the right and then 10 turns to the left. Do the same for all ten
|
|
of them.
|
|
|
|
Now apply power to the unit check to see that you have power in the chips
|
|
by putting the positive lead of your volt meter on pin 7 and the negative
|
|
lead on pin 12. If you do not have anything there turn off the unit and
|
|
RECHECK THE WIRING.
|
|
|
|
When you get the right voltages on the chips, connect a diode to a piece
|
|
of wire (look at fig. 2 for the orientation of the diode) from ground to any
|
|
pot at point T (look carefully at the schematic for point T it is labeled
|
|
T1-T10 for all pots). You should be able to hear a tone, if not disconnect
|
|
the lead and place the speaker close to your ear and if you hear a chirp-like
|
|
sound, this means that the two VCO'S are working if you don't, it means that
|
|
either one or both of the VCO'S are dead. So in this case it is always good
|
|
to have an ocilloscope on hand. Disconnect the speaker from the circuit and
|
|
hook the ocilliscope to 1 of the leads of the speaker & the ground from the
|
|
scope to the ground of the battery. Connect again the ground lead with the
|
|
diode connected to it from ground to any pot on the VCO that you are checking
|
|
and you should see a triangle wave if not turn the pot in which you are
|
|
applying the ground to until you see it. When you do see it do the the same
|
|
for the other VCO to make sure it is working. (amplitude is about 2VAC). When
|
|
you get the two VCO's working you are set for the adjustment of the
|
|
individuals pots.
|
|
|
|
|
|
Adjustment
|
|
----------
|
|
|
|
Disconnect the speaker from the circuit and connect a freq. counter (the
|
|
positive lead of the counter to one of the speakers leads that belongs to
|
|
VCO#1 or connect it to pin 14).
|
|
|
|
Connect the negative lead to the battery negative and connect the jumper
|
|
lead with the diode from ground to pot number 1.T1. ( the first pot number
|
|
1 point T1) if you got it working you should hear a tone and get a reading
|
|
on the counter. Adjust the pot for a freq. of 1700HZ and continue doing the
|
|
same for pots 2-5 except that they get differents freqs. which are:
|
|
|
|
$$$$$$$$$$$$$$
|
|
$ P1= 1700hz $
|
|
$ P2= 1300hz $
|
|
$ P3= 1100hz $
|
|
$ P4= 900hz $
|
|
$ P5= 1500hz $
|
|
$$$$$$$$$$$$$$
|
|
|
|
Now disconnect the freq. counter from the speaker lead of VCO#1 or from
|
|
pin 14 (which ever you had it attached to at the beginning) and connect it
|
|
to the speaker lead of VCO#2 or to pin 14 of VCO#2 and make the same
|
|
adjustments to P6-10.
|
|
|
|
$$$$$$$$$$$$$$$
|
|
$ P6= 1100hz $
|
|
$ P7= 700hz $
|
|
$ P8= 900hz $
|
|
$ P9= 2600hz $
|
|
$ P10= 1500hz $
|
|
$$$$$$$$$$$$$$$
|
|
|
|
When you finish doing all of the pots go back and re-check them.
|
|
|
|
|
|
Keyboard
|
|
--------
|
|
|
|
If you look at FIG-2 you will see that the keys are simple switches.
|
|
Connected to a ground and two diodes on the other end. these diodes are used
|
|
to simplify the construction of the keyboard because otherwise the
|
|
distribution of the ground signal for both VCO'S would have been done
|
|
mechanically. The diode will go to VCO#1 and the other will go to VCO#2.
|
|
FIG-3 shows the arrangement of the keys on the keyboard.
|
|
|
|
|
|
Below is a table that will help you connect the keys to the required VCO's
|
|
pots.
|
|
|
|
(-FIG 2-)
|
|
-----!-----!--------!--------!-------
|
|
! ! ! !
|
|
TO ! TO ! FREQ ! FREQ ! KEY
|
|
POT ! POT ! OUT: ! OUT: !
|
|
ON ! ON ! ! !
|
|
VCO1! VCO2! ! !
|
|
-----!-----!--------!-------%!-------
|
|
1 ! 06 ! 1700hz ! 1100hz ! C
|
|
2 ! 10 ! 1300hz ! 1500hz ! 0
|
|
1 ! 10 ! 1700hz ! 1100hz ! E
|
|
4 ! 07 ! 0900hz ! 0700hz ! 1
|
|
3 ! 07 ! 1100hz ! 0700hz ! 2
|
|
3 ! 08 ! 1100hz ! 0900hz ! 3
|
|
2 ! 07 ! 1300hz ! 0700hz ! 4
|
|
2 ! 08 ! 1300hz ! 0900hz ! 5
|
|
2 ! 06 ! 1300hz ! 1100hz ! 6
|
|
5 ! 07 ! 1500hz ! 0700hz ! 7
|
|
5 ! 08 ! 1500hz ! 0900hz ! 8
|
|
5 ! 06 ! 1500hz ! 1100hz ! 9
|
|
- ! 09 ! ------ ! 2600hz ! X
|
|
|
|
Remember that in FIG-2 it's the same for each key except the "X" key,
|
|
which only takes one diode.
|
|
|
|
|
|
few KEYS to the diagram:
|
|
|
|
Cx is capacitor #x Denoted by: ---| |
|
|
---
|
|
|
|
Px is Pot or Variable resistor #x Deno
|
|
ted by :/
|
|
|
|
\
|
|
|
|
/<--
|
|
\
|
|
Rx is resistor #x Denoted by /\/\/\/\
|
|
|
|
SCHEMATICS
|
|
|
|
The XR-2207 chip is a Voltage-Controlled Oscillator and a 14 pin device
|
|
thus you must be very careful when soldering the parts to this device. It is
|
|
a little dificult to actually draw a schematic on an 80 character screen
|
|
using limited graphics, but I will give
|
|
it a try.
|
|
|
|
TO GND_____________
|
|
|
|
|
___
|
|
C2 C3 ___
|
|
_||_ |
|
|
| | _____|__9v+
|
|
| | | |
|
|
` ` ` ` ` ` ` |
|
|
------------------------------- |
|
|
7 6 5 4 3 2 1 | |
|
|
| < |
|
|
|8 9 10 11 12 13 14| |
|
|
------------------------------- |
|
|
` ` ` ` ` ` ` |
|
|
| | |
|
|
--| |--------| | |
|
|
|C1 R2 | R1 |
|
|
GND ______|___/\/\/\/\______|_____/\/\/\/\______|
|
|
|
|
|
|
is is a diagram of how to locate the different pins on the chip.
|
|
Please notice that pin one (1) is the closest to the notch on top of the
|
|
chip. The first thing we'll do is to connect power to the chip (remember that
|
|
you need to build two (2) of these to get a complete system) this is
|
|
accomplished by connecting the positive wire of the battery lead to pin#1 one
|
|
leg of R1 and R2 is soldered to pin#11. The other leg of R1 goes to pin 1
|
|
or to the d. C1 goes between pin 10 and ground. The timing capacitor or C2
|
|
goes between pins 2 and 3 of the chip. Pins 8 and 9 should be grounded to
|
|
ground. Pin 14 is the output and this is where one leg of C4 (C3 goes on the
|
|
other VCO) in series with R3 (the same goes for the other VCO) and to one
|
|
lead of the speaker.
|
|
|
|
The trimmer pots P1 to P10 should be grouped in groups of 5 pots each.
|
|
The way you group it is by soldering one end of the pot to each other leaving
|
|
the wiper and the other end free.
|
|
|
|
| This end goes to pin 6 of the chip
|
|
|
|
|
_____________|_____________
|
|
/ / / / /
|
|
\ \ \ \ \
|
|
/<- /<- /<- /<- /<-
|
|
\ | \ | \ | \ | \ |
|
|
/ | / | / | / | / |
|
|
| | | | |
|
|
| | | | |
|
|
P1 P2 P3 P4 P5
|
|
|
|
|
|
And finally this is the way each key should be wired.
|
|
|
|
diode
|
|
he contact of the
|
|
|--------- \------ key
|
|
to Px ------>|-----| |
|
|
diode |
|
|
-----
|
|
--- Ground
|
|
|