303 lines
14 KiB
Plaintext
303 lines
14 KiB
Plaintext
|
|
|
|
|
|
|
|
|
|
|
|
|
|
How to make PLT -Professional Lock Tools-
|
|
|
|
The making and possessing of lock-opening tools may be regulated by state
|
|
and local laws. Check these before you start. Although all of the
|
|
techniques and materials discussed herein will work, I accept no liability
|
|
whatsoever regarding use of this information.
|
|
|
|
The mere insertion of a lockpick in a keyway constitutes "entry" (as in
|
|
"breaking and entering"). Everything you have heard about life in the can
|
|
is true, so if you want to score big, take my advice and run for office
|
|
that's legal!
|
|
|
|
-Eddie The Wire
|
|
|
|
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ TOOLS AND SUPPLIES ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
A. TOOLS
|
|
1. Grinding machine with 1/4" - 3/4" coarse wheel. (A lot of
|
|
metal must be removed in some plt, so a file would be too
|
|
slow and tiring. A cheap alternative is an arbor mounted
|
|
stone chucked in an electric drill.)
|
|
2. 6" - 10" flat mill cut file
|
|
3. Gun blue
|
|
4. Small ruler
|
|
5. Paint masking tape.
|
|
6. Scribe or nail
|
|
B. SUPPLIES
|
|
1. 1/4" Spring steel (The do-it-yourself sewer snakes sold at
|
|
hardware stores work well. It is also pre blued.)
|
|
2. Feeler gauge stock, 1/2" x .025" x 12" and 1/2" x .035" x 12"
|
|
3. Hacksaw blades (1/2" x 12")
|
|
4. Two extra-cheap pin-tumbler rim cylinder locks. (Buy two of
|
|
the same brand.)
|
|
5. And of course, a quiet, well-lighted place to work is good.
|
|
|
|
|
|
Also, any hand tools you may have will make the work that much easier. The
|
|
above should be considered the bare minimum. Let me emphasize that the
|
|
purchase of a small bench grinder may involve a medium expense, but is is
|
|
well worth it in time saved.
|
|
|
|
|
|
Your basic set of PLT will consist of one diamond, two lifters, and two
|
|
tension wrenches, This will allow you to work 90% of the locks you
|
|
encounter.
|
|
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ BEGINNING MEASUREMENTS ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
Several measurements are necessary to size the PLT to a particular lock,
|
|
and also to you own opening technique. First (alpha) measure the distance
|
|
from the key stop (the part of the key that butts against the lock face
|
|
and prevents further insertion) to the exact bottom of the farthest pin
|
|
cut, as shown in figure 1. Next (beta) measure the distance between two
|
|
adjacent pin cuts. Finally grab a pencil (you should be writing down these
|
|
measurements) and pretend it is a lockpick, holding the eraser end up to a
|
|
lock as you usually hold your lockpick, If you have never used a pick
|
|
before, hold it in your usual pencil grip. Mark the point at which the
|
|
pencil shaft no longer touches any part of your hand, and then measure
|
|
from the eraser to that mark for the gamma measurement.
|
|
|
|
|
|
|
|
³<---total key length-->³
|
|
³ ³
|
|
³ ³
|
|
³ ³<--alpha-->³ ³
|
|
³ ³ ³ ³
|
|
³ ³ beta>³ ³< ³
|
|
³ ÛÛÛÛÛÛ ³ ³ ³ ³
|
|
³ÛßÛÛÛÛÛÛÄ/\_/\Ä/\_/\-/\³
|
|
ÛÜÛÛÛÛÛÛÍÍÍÍÍÍÍÍÍÍÍÍÍÍ/
|
|
ÛÛÛÛÛÛ
|
|
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ ROUGH PROFILE BLANKS ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
At this point we begin making rough profile blanks, or RPB. Add one alpha
|
|
dimension, one gamma dimension, and three beta dimensions together. The
|
|
total is the RPB overall length. With luck, it may be less than 4 inches,
|
|
enabling you to cut three RPB from one piece of stock. If you are using
|
|
painted hacksaw blades, fine lines can be scribed directly onto them.
|
|
Plain blades and feeler stock must be blued (with your gun blue) to accept
|
|
layout lines. Your best bet is using the plumers snake if you can find it.
|
|
This stuff is preblued and beats the hell out of hacksaw blades.
|
|
|
|
Scribe your RPB length lines and cut them apart by grinding on the face of
|
|
the stock. In any grinding, the heat produced can quickly rise to levels
|
|
hot enough to un-temper the steel. If any part of a PLT becomes un-
|
|
tempered (indicated by a dark blue or straw-colored area), it will easily
|
|
bend at that point and make pin manipulation impossible. Also, no thin
|
|
steel shapes can be retempered by heating and quenching because they will
|
|
warp badly. A burned pick is a ruined one. A good way to keep grinding
|
|
time short is counting to three while grinding. cooling the PLT in cold
|
|
water, and then starting over with the count. As the cross-section gets
|
|
smaller and there is less material to carry excess heat away, only grind
|
|
for a count of one or two before cooling. Having the water immediately
|
|
below the wheel saves a lot of time and motion. Sharp angles and points on
|
|
PLT really heat up fast, so cool frequently. Holding the PLT in bare
|
|
fingers while grinding is another good way to avoid burning (the steel, at
|
|
least).
|
|
|
|
|
|
|
|
ÜÜ ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜ
|
|
ÛÛÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛÛ
|
|
sample RPB
|
|
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ THE DIAMOND PICK ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
At this point, collect keys for your two sample locks and examine the
|
|
different bitting depths. You are looking for the maximum height
|
|
difference between two adjacent bitting appreciable height difference, but
|
|
occasionally just by chance, there will be nothing but slight differences
|
|
in biting depths. If this happens, examine any keys in your pocket that
|
|
have the same alpha/beta dimensions, looking for an appreciable height
|
|
difference (which we will call a delta dimension). Once you find the
|
|
maximum delta dimension, trace that section of the key directly onto an
|
|
RPG. The object is to duplicate the exact angles and height of that
|
|
selected part of key bitting on the RPB. Remember to keep the bottom of
|
|
the lower of the two bitting depths flush with the top of the shank on the
|
|
tool. When you have traced this, grind to the new outline, taking special
|
|
care not to lessen the delta dimension at all by grinding the top of the
|
|
pick end. Your finished product should look like a diamond. If it has a
|
|
flat spot at the top, grind to eliminate the flat spot, while keeping the
|
|
height the same.
|
|
|
|
As you expand beyond a basic PLT set, you may want diamond picks with
|
|
lower height diamonds (delta dimensions). Note: A pick cut to the maximum
|
|
delta dimension can lift a pin to the necessary height without the shank
|
|
of the pick binding and possibly un-picking the lower adjacent pin. A PLT
|
|
with a lower height delta is, however , useful in special situations and
|
|
other makes/models of locks. To produce these smaller PLT, Simply trace
|
|
your maximum delta pick directly onto a RPB, and then continue the process
|
|
shown but past the point that is shown to stop grinding. This will
|
|
effectively lower the diamond to any desired height. Remember to keep the
|
|
angle the same or the pick will not easily slide in under the pins.
|
|
|
|
|
|
|
|
ÚÄÄÄÄÄgrind to eliminate flat
|
|
³
|
|
|
|
Successive key cutsÄÄÄÄÄÄÄ> //ÄÄ\
|
|
lower diamond height // / /^\______________________
|
|
ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄ
|
|
|
|
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ THE LIFTER PICK ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
The working end of a lifter is merely an upswept curve with a small flat
|
|
spot on top to hold the pin. Remember, a diamond is pointed, but a lifter
|
|
has a flat on the top. You can cut these PLT easily by tracing your
|
|
maximum delta profile on a RPB and then making modifications. In this
|
|
re-designing, make sure that the distance from the middle of the flat top
|
|
of the PLT to the beginning of the upsweep is at least as great as the
|
|
beta dimension. If not, the sweep might lift or bind on an adjacent pin.
|
|
Make this PLT in two delta dimensions to complete the pick components of
|
|
the basic PLT set. The smallest delta dimension among your sample keys
|
|
would be a good choice for a second pick size.
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ SNAKE PICKS ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
Besides lifter and diamond profiles of various delta heights, there are
|
|
also half-rounds and multiple-cut PLT (usually called snake picks), Both
|
|
types are useful when "raking" the lock with a diamond fails, and
|
|
"lifting" is too tedious. (To understand this fully, you should have some
|
|
lock-picking theory down, but if you don't just trust me.) Half-round
|
|
profiles are laid out by marking the delta dimensions on a RPB and then
|
|
tracing various curves whose tops are no higher than this delta dimension.
|
|
The base of the arc should be wider than two beta dimensions so that part
|
|
of the curve will lift two or more adjacent pins, unlike diamonds and
|
|
lifters which work only one pin at a time. Since the arc base is wider
|
|
than two beta dimensions a special RPB should be made for this and the
|
|
"snake" PLT. A snake PLT attempts to duplicate a two/three/four pin
|
|
portion of actual key profile, thereby holding up a group of pins
|
|
simultaneously that would require great skill to pick individually. I
|
|
suggest that you not use RPB for these profiles, but instead lay out a
|
|
blank with lines for four beta dimensions as shown:
|
|
|
|
|
|
<ÄÄÄÄÄÄÄÄÄÄfour beta dimensions
|
|
³ ³ ³ ³
|
|
_____³_³_³_³_______________________________________
|
|
³ /^\_/^\|____________/ ³
|
|
Ä/ÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÄÙ
|
|
|
|
|
|
|
|
Cutting then becomes a matter of selecting a good profile, tracing and
|
|
cutting it out. Notice that you can make up a composite of individual key
|
|
bitting cuts selected and arranged according to any to any pattern by
|
|
marking the depth of cut only, and then connecting the depths with
|
|
straight lines. Just remember to never exceed the delta dimension between
|
|
adjacent cuts, or the PLT will not work smoothly or at all, because of too
|
|
steep angles on the bitting cuts.
|
|
|
|
The problem is: What sequence or profile of cuts works best? How many cuts
|
|
should be used, and how deep? since the object is to duplicate key action
|
|
and all keys are different there is no "best" profile for all locks.
|
|
|
|
One approach is to cut a profile that works on a sequence difficult to
|
|
open by lifters and diamonds, such as:
|
|
* deep, shallow, deep, medium
|
|
* deep, shallow, deep
|
|
* deep, shallow, medium
|
|
|
|
These lift one or two pins high, while lifting adjacent pins only a little
|
|
something lifters cannot do. Experiment also with the following profiles:
|
|
* deep, medium, shallow, deep
|
|
* medium, deep, shallow
|
|
* deep, deep, shallow, medium
|
|
|
|
Another concept to try out is half-depth profiles. Keys are usually cut
|
|
according to steps or increments of cut. An average system might have 9 -
|
|
10 steps of key bitting depth, even though not all are present on one key.
|
|
buy cutting one or more of your PLT bitting depths either high or low by
|
|
exactly one-half of this step, you may increase the number of combinations
|
|
the PLT will work. This is especially true of worn or cheap locks with
|
|
loose-fitting parts. The rule here is experiment. Some profiles may not
|
|
open any locks, in which case they can be re-cut to other profiles.
|
|
Usually a "snake" PLT is a last resort, but some can be very valuable.
|
|
|
|
|
|
|
|
ÕÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ͸
|
|
³ TENSION WRENCHES ³
|
|
ÔÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍÍ;
|
|
|
|
Two tension wrenches are required to complete the basic PLT set. Start by
|
|
cutting off a 6 inch length of .060 - .090 diameter music wire and bend as
|
|
shown
|
|
|
|
|
|
|
|
°
|
|
°
|
|
ÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÜÛ
|
|
º
|
|
º
|
|
|
|
|
|
|
|
Now go to the wheel and grind the flats indicated, the object being to
|
|
obtain ends wit rectangular cross-sections. Test for a tight fit as the
|
|
grinding progresses by trying the tool in a keyway. Try also to grind
|
|
another wrench in which the flats have a slight taper getting smaller near
|
|
the tip. This will permit a tight wedge fit and thus increase the feel and
|
|
control of the wrench. Wrenches with a loose keyway fit seem to work
|
|
better with jerking or raking pick procedures . While wrenches with a
|
|
tight fit give more control in lifting pick procedures.
|
|
|
|
|
|
Or you can use RPB stock to make tension wrenches. The RPB stock is to
|
|
wide for a tension wrench you will need to make it thinner. I usually do
|
|
this after I've put the proper bends on it you can bend it similar to the
|
|
wrench shown above or like this:
|
|
|
|
|
|
|
|
|
|
ÉÍÍÍÍÍßßßßßßßßßßßßßßßßßßßßßßßßßßß
|
|
º ^ 45ø twist
|
|
|
|
|
|
|
|
Make a 90ø bend 3/4" from the end of the RPB stock put a 45ø twist about
|
|
1/2" from the 90. Now grind it down till it is about 1/8" wide. You need a
|
|
few of these altering only the end to produce different widths.
|
|
|
|
This completes the basic PLT set. Using this set you can open 90% of ALL
|
|
the locks you'll encounter.
|
|
|