150 lines
5.0 KiB
Plaintext
150 lines
5.0 KiB
Plaintext
AST RESEARCH TECHNICAL BULLETIN TB-0279 05/29/87
|
|
|
|
|
|
AST PCNET/PCNET II QUICK REFERENCE MATERIAL
|
|
|
|
|
|
Due to the discontinuance of AST PCnet and PCnet II Local
|
|
Area Network (LAN) products, effective April 15, 1987, (the
|
|
generic term "AST-PCnet" refers to both AST-PCnet and PCnet
|
|
II) only limited support will be available for these
|
|
products. Users who are having problems or wish to expand
|
|
their AST PCnet systems will be directed to upgrade to AST-
|
|
ADVANCED NETWARE or the AST-NETBIOS OPTION for network
|
|
software needs. Existing AST-PCnet hardware users who wish
|
|
to expand may do so via the bridging capabilities provided
|
|
with AST-Advanced Netware. The following information was
|
|
gathered from AST Technical Support, Marketing, and
|
|
Engineering documentation, or PCnet manuals in reference to
|
|
PCnet hardware exclusively.
|
|
|
|
|
|
HARDWARE COMPATIBILITY
|
|
|
|
|
|
PCnet hardware compatibility is dependent on the hardware
|
|
configuration. Providing there are no I/O address range,
|
|
IRQ line, DMA channel or network ID conflicts and the cables
|
|
are properly terminated, the cards should function in IBM
|
|
PC, XT AT and compatibile computers. The boards have been
|
|
tested successfully in machines operating at 4.77, 6, 8, and
|
|
10 megahertz. Most incompatibility problems are the result
|
|
of a non-IBM ROM BIOS or non-IBM MS-DOS. Recently, it has
|
|
been discovered that PCnet adapter cards are adversely
|
|
affected by the AST-3G and all other EGA boards. Current
|
|
EGA users should be guided towards the AST-RSN to avoid any
|
|
problems.
|
|
|
|
|
|
AST-PCNET I HARDWARE OVERVIEW
|
|
|
|
|
|
The AST-PCnet I Local Area Network (LAN) adapter board
|
|
includes an interface to the network and runs at 800k bits
|
|
per second over 75 ohm CATV coaxial cable using CSMA/CD
|
|
access method. The maximum cable length is 2,000 feet using
|
|
RG 59 B/U cable, or 5,000 feet using RG 11/U cable.
|
|
|
|
|
|
|
|
AST PCNET I HARDWARE CONFIGURATION
|
|
|
|
|
|
The AST PCnet I board came factory configured as follows:
|
|
|
|
1. I/O address range 380-38f hex (not alterable)
|
|
|
|
2. IRQ line 2
|
|
|
|
3. DMA channel 1 (not alterable)
|
|
|
|
|
|
Each node (PC) on the network must have a unique network ID
|
|
number. The ID numbers are hexadecimal numbers ranging from
|
|
11 to EF. To ensure future compatibility, assign network
|
|
IDs in order.
|
|
|
|
DIP switch SW-2 on the AST-PCnet I board sets the ID number.
|
|
(see table 1-1 on page 6 for Network ID select.)
|
|
|
|
The two PCs at the extreme ends of the network cable must be
|
|
terminated with 75-ohm terminators.
|
|
|
|
Refer to page 3 for cabling diagram, and pages 4 and 5 for
|
|
hardware layout.
|
|
|
|
|
|
NOTE: As a portion of the data is in pictorial form, it is not
|
|
included here. To obtain a complete copy of this
|
|
technical bulletin, contact:
|
|
|
|
AST RESEARCH, INC.
|
|
2121 Alton Avenue
|
|
Irvine, California 92714-4992
|
|
|
|
Attention: Product Support
|
|
(Technical Bulletin)
|
|
|
|
|
|
AST-PCNET II HARDWARE OVERVIEW
|
|
|
|
|
|
The AST-PCnet II Local Area Network (LAN) adapter board
|
|
includes an interface to the network and runs at 800k bits
|
|
per second over Twisted Wire Pair (TWP) cable using CSMA/CA
|
|
access method. The maximum cable length is 500 feet (150
|
|
meters) of Belden type 8442 TWP cable (or equivalent cable
|
|
rated 120 ohm). Up to 32 PCs can be connected to each 500-
|
|
foot segment of TWP cable.
|
|
|
|
In addition to the standard model, the AST PCnet II board
|
|
was also available with the repeater board circuitry that
|
|
allows the extension of the length of the network past the
|
|
500 foot limit. The distinguishing features of the repeater
|
|
board are two RJ-11 connectors (J1 and J2), where as the
|
|
standard board has only one connector (J1). It was possible
|
|
to connect up to four repeater boards to extend the network
|
|
to a maximum 2,500 feet.
|
|
|
|
|
|
|
|
AST-PCNET II HARDWARE CONFIGURATION
|
|
|
|
The AST-PCnet II board came factory configured as follows:
|
|
|
|
1. I/O address range 380-38F hex
|
|
|
|
2. IRQ line 2
|
|
|
|
3. DMA channel 1 (not alterable)
|
|
|
|
4. Terminated (jumpered at T2)
|
|
|
|
|
|
Each node (PC) on the network must have a unique network ID
|
|
number. The ID numbers are hexadecimal numbers ranging from
|
|
11 to EF. To insure future compatibility, assign network
|
|
IDs in order.
|
|
|
|
Dip switch SW-1 on the AST PCnet II board sets the ID
|
|
number. (See table 1-1 on page 6 for Network ID select.)
|
|
|
|
The two PCs at the extreme ends of the network cables must
|
|
be terminated by placing a jumper in the T-2 position.
|
|
|
|
Refer to page 8 for cabling diagram, pages 9 and 10 for
|
|
hardware layout, and 11 and 12 for address and terminator
|
|
selection.
|
|
|
|
|
|
NOTE: As a portion of the data is in pictorial form, it is not
|
|
included here. To obtain a complete copy of this
|
|
technical bulletin, contact:
|
|
|
|
AST RESEARCH, INC.
|
|
2121 Alton Avenue
|
|
Irvine, California 92714-4992
|
|
|
|
Attention: Product Support
|
|
(Technical Bulletin)
|
|
|